Please use pdf to print the instruction manual.
Contents
Conventions used in this manual
Simultaneous processing capabilities
2 - Names and Functions of Parts
Special touchscreen operations
ST IN 1–2/FX RTN 1–4 Module Home Screen
MIX 1–22 and MAIN L/R Master Module Home Screen
Installing expansion cards (sold separately)
Setting the built-in clock date and time
Connecting and disconnecting SD cards and USB flash drives
SD card write protection switches
Preparing SD cards and USB flash drives for use
SD cards and USB flash drives used by this unit
4 - Mixer configuration and settings
Setting the sampling frequency
Operation restriction during ON AIR Tally input
Automatic muting of monitor signals using the Location function
USER DEFINED CONTROLS screen structure
Control setting on USER DEFINED CONTROLS Screen
Setting the footswitch polarity
Default settings for LAYER KEYS 1–7
Custom layer assignment operation procedures
Selecting the custom layer slot button followed by the module button
Selecting the module button followed by the custom layer slot button
Making monitor output settings
Making solo and built-in oscillator settings
Mounting of devices connected to the Dante network
Mounting devices that are not on the Dante network
Setting control privileges after mounting
Alerts and errors shown related to the SB-16D
Restrictions when routing during 96kHz operation with Dante Controller
Preamp control as a Sonicview I/O expansion
GPIO Extension Settings Screen
Using GPIO extension functions
Procedures for Dante connection with SB-16Ds
Dante connections with SB-16Ds
Procedures for Dante connection with this unit and one SB-16D
Switched (daisy chain) connection
Changing sampling frequencies and bit depths with Dante Controller
When an IF-DA64 (Dante) card is installed
Precautions when using an IF-DA64
When an IF-AE16 (AES/EBU) card is installed
When an IF-MA64/EX or IF-MA64/BN (MADI) card is installed
When an IF-AN16/OUT (analog output) card is installed
When an IF-MTR32 (multitrack recording) card is installed
When an IF-ST2110 (ST 2110) card is installed
Where the PORT LABEL display mode setting is applied
Where the Sub MODULE LABEL display mode setting is applied
Where the Main MODULE LABEL display mode setting is applied
USER LABEL (INPUT PORT / OUTPUT PORT) Screen
IP Address/Subnet Mask/Default Gateway setting procedures
CH 1–40/ST IN 1–2 MODULE (OVERVIEW) Screens
CH 1–40/ST IN 1–2 MODULE (INPUT) Screens
Setting inputs sources for multiple channels at the same time in batches
Direct out signal output routing
Insert input and output routing
MIX 1–22 and MAIN L/R Master MODULE (OVERVIEW) Screens
MIX 1–22 and MAIN L/R Master MODULE (OUTPUT) Screens
Setting output ports for multiple channels at the same time in batches
INSERT SEND PORT SELECT screen
INSERT RETURN PORT SELECT screen
CH 1–40 MODULE (OVERVIEW) Screens
ST IN 1–2 MODULE (OVERVIEW) Screens
FX RTN 1–4 MODULE (OVERVIEW) Screens
MIX 1–22 and MAIN L/R Master MODULE (OVERVIEW) Screens
Setting digital trim values in batches
MODULE (GATE/EXPANDER/DE-ESSER) screens
MODULE (Audio Follow Video) Screen
AFV TRIGGER SOURCE SELECT Screen
Pasting parameters that can be operated independently for left and right in stereo modules
7 - Other module parameter setting screens
MIX 1–22 bus SEND OVERVIEW Screen
FX 1–4 bus SEND OVERVIEW Screen
MAIN L/R bus SEND OVERVIEW Screen
DCA (Digital Control Amplifier) functions
Setting and editing user module labels
Preparations and procedures for using the AUTO MIXER function
AUTOMATIC MIXER Screen display procedures
AUTOMATIC MIXER content explanation
8 - Saving and recalling setting data
Using snapshot functions at the top of the Menu Screen
Using STORE at the top of the Menu Screen
Storing snapshots on the Snapshot List Screen
Storing using a control set on the USER DEFINED CONTROL Screen
Using RECALL at the top of the Menu Screen
Recalling snapshots on the Snapshot List Screen
Recalling using a control set on the USER DEFINED CONTROL Screen
SNAPSHOT IMPORT / EXPORT screen
Restoring factory default settings
9 - Various information displays
OPEN SOURCE SOFTWARE LICENSE Screen
Sonicview 16/24 Error Screen SYSTEM error/alert message list
SD cards and USB flash drives used by this unit
BROWSE Screen for recording folder selection
11 - USB audio interface functions
Installing the dedicated software
Installing the Windows dedicated software
Windows dedicated software installation procedures
Uninstalling the dedicated software
Uninstalling the Windows dedicated software
Opening the dedicated software
Simultaneous ASIO/WDM playback
When the sample rates are the same
When the sample rates are different
Setting procedures for use with OBS Studio and other streaming applications
Windows computer sound settings
SD cards used by IF-MTR32 units
When in LIVE RECORDING MODE or VIRTUAL SOUND CHECK MODE
Using the AUTO ROUTING function
When in VIRTUAL SOUND CHECK MODE
REC READY/INPUT MONITOR settings
MTR output according to REC READY and INPUT MONITOR settings
MULTI TRACK RECORDER - MENU Screen
MTR - MENU Screen when in LIVE RECORDING MODE
MTR - MENU Screen when in OVERDUB MODE
MULTI TRACK RECORDER - BROWSE Screen
BROWSE MTR Screen showing project list
BROWSE MTR Screen showing take list
Viewing project and take lists
Selecting the MTR input source
Manual input routing to the MTR
Checking recorded audio (playing recordings)
Inputting the location time to locate
Using the footswitch to punch in/out
Automatic punch in/out function
Setting the punch in/out points
Setting pre roll and post roll points
Rehearsing punching in and out
Using automatic punching in and out
Undoing auto punch in/out operations (UNDO function)
Undoing the most recent punch in/out operation
Importing files that have been recorded on other devices
Using imported files with this unit
Moving forward/backward one at a time
Moving by selecting from a list
Selecting from a list and deleting
Moving to the mark and deleting
13 - IF-ST2110 expansion cards
HOME (Source / Destination) page
14 – External control over a network
Using TASCAM Sonicview Control to control this unit
Monitoring and controlling this unit with Ember+
Monitoring this unit with SNMP
List of parameters supported by this unit for SNMP monitoring
15 – Fader and touchscreen calibration
Starting and ending calibration mode
Starting up in calibration mode
Calibration mode menu operations
16 - List of shortcut operations
Changed settings are forgotten
Touchscreen operations are not possible
Parameters on the touchscreen can be operated but do not affect the sound
18 - Specifications and ratings
Simultaneous processing capabilities
Mic amp EIN (equivalent input noise)
Analog audio input and output ratings
Digital audio input/output ratings
Dante PRIMARY/SECONDARY connectors
Other input and output specifications
Operating system and computer requirements
Computer hardware requirements
Computer hardware requirements
Sonicview 16/24 Mixer Basic Parameters
Sonicview 16/24 Mixer Basic Parameters (FX)